![](/globalassets/mediavalet/web-assets/pictures/expander/manuals/expander.png?mode=pad&width=600)
Installation Instructions
Straight Pin
5.4
![](/globalassets/mediavalet/web-assets/pictures/expander/manuals/expander_manual_product_straight_pin.png?mode=pad&width=600)
Following these instructions will ensure that the Expander System is installed correctly and the pivot life is prolonged.
Congratulations! You have purchased a custom engineered solution to the pivot wear problem on your machine. Contact your dealer or Expander before proceeding if you have any questions.
Expander System pivot pin comes with a warranty against lug wear of 10 years / 10 000 hours in operation (whichever comes first) from the date of purchase.
A. Female axle. B. Male axle with spanner nut. C. Male axle with nut.
![](/globalassets/mediavalet/web-assets/pictures/expander/installation-instructions/straight-pin/straight_pin_three_axles.png?width=800)
1 Bolt. 2 Washer. 3 Sleeve. 4 Axle (Pin). 5 Spanner nut. 6 Nut.
Preparation
![](/globalassets/mediavalet/web-assets/pictures/expander/installation-instructions/01_preparation_removal.png?mode=pad&width=600)
Remover qualquer bucha para eliminar desgaste futuro entre bucha e olhal de montagem.
![](/globalassets/mediavalet/web-assets/pictures/expander/installation-instructions/02_preparation_repair.png?mode=pad&width=600)
Reparar qualquer estrutura danificada ex. Trincas ou olhais tortos.
![](/globalassets/mediavalet/web-assets/pictures/expander/installation-instructions/03_preparation_cleaning.png?mode=pad&width=600)
Suavize irregularidades na superfície dos furos dos olhais.
![](/globalassets/mediavalet/web-assets/pictures/expander/installation-instructions/04_preparation_min_max.png?mode=pad&width=600)
A diferença entre diâmetro min. e max. no desgaste do olhal deve ser dentro de .06” (1.5 mm) para o correto encaixe das luvas.
ATTENTION! If the worn lugs diameter at any point is 2 mm (.080”) or more over original lug diameter contact your dealer or Expander System. You will need oversized sleeves.
Installation
![](/globalassets/mediavalet/web-assets/pictures/expander/installation-instructions/05_installation_grease.png?mode=pad&width=600)
Engraxe as luvas e eixo com a graxa disponível, de preferência graxa grafitada. NÃO ENGRAXE AS ROSCAS.
![](/globalassets/mediavalet/web-assets/pictures/expander/installation-instructions/06_installation_note.png?mode=pad&width=600)
NOTA! Se aplicável: posicione a saída de graxa a 90 graus para forçar a direção para minimizar a concentração de estresse na saída.
![](/globalassets/mediavalet/web-assets/pictures/expander/installation-instructions/straight-pin/06_installation_straight_pin.png?mode=pad&width=600)
Insira o pino e o posicione nos furos. Instale as luvas, em seguida as arruelas de tensão e espaçadores. Aperte os espaçadores com o torque específico da tabela ao lado.
Torque recommendations
![](/globalassets/mediavalet/web-assets/pictures/expander/installation-instructions/08_hex_bolts.png?mode=pad&width=800&heightratio=0.3333)
Parafusos hexagonais
Torques M12-M24 ± 10%, M30... +30/-0%
M12 | M14 | M16 | M20 | M24 | M30 | M36 | M42 | |
Nm | 70 | 115 | 175 | 350 | 500 | 600 | 700 | 900 |
lb-ft | 52 | 85 | 129 | 258 | 369 | 443 | 516 | 664 |
![](/globalassets/mediavalet/web-assets/pictures/expander/installation-instructions/09_standard_nut.png?mode=pad&width=800&heightratio=0.3333)
Porcas hexagonais: Altura padrão
Torques M12-M24 ± 10%, M30... +30/-0%
M12 | M14 | M16 | M20 | M24 | M30 | M36 | M42 | |
Nm | 65 | 115 | 175 | 250 | 350 | 500 | 600 | 700 |
lb-ft | 48 | 85 | 129 | 184 | 258 | 369 | 443 | 516 |
![](/globalassets/mediavalet/web-assets/pictures/expander/installation-instructions/10_low_nut.png?mode=pad&width=800&heightratio=0.3333)
Porcas hexagonais: Altura baixa
Todos os Torques ± 10%
M12 | - | M16 | M20 | M24 | M30 | - | - | |
Nm | 60 | - | 125 | 200 | 275 | 350 | - | - |
lb-ft | 44 | - | 92 | 148 | 203 | 258 | - | - |
![](/globalassets/mediavalet/web-assets/pictures/expander/installation-instructions/11_spanner_nut.png?mode=pad&width=800&heightratio=0.3333)
Porcas redondas
Todos os Torques ± 10%
M17 | M25 | M35 | M45 | M55 | M65 | M75 | M85 | |
Nm | 50 | 120 | 250 | 500 | 600 | 700 | 800 | 900 |
lb-ft | 37 | 89 | 184 | 369 | 443 | 516 | 590 | 664 |
Final Check
![](/globalassets/mediavalet/web-assets/pictures/expander/installation-instructions/12_final_check_initial_torque2.png?mode=pad&width=600)
Após o torque inicial movimente a máquina em sua amplitude total várias vezes e reconfirme o torque. Verifique o torque após 10 horas, 40 horas e em intervalos regulares de serviço para assegurar o correto assentamento das luvas.
![](/globalassets/mediavalet/web-assets/pictures/expander/installation-instructions/13_final_check_min_distance.png?mode=pad&width=600)
Verifique se existe uma distância de no mínimo 0.5 mm entre a arruela e o olhal. ATENÇÃO! Se a arruela estiver em contato com o olhal, contate seu revendedor do Sistema Expander.
Dismounting
![](/globalassets/mediavalet/web-assets/pictures/expander/installation-instructions/14_dismounting_unscrewing.png?mode=pad&width=600)
Para desmontar o Sistema Expander, desaparafuse os espaçadores em ambas as extremidades e remova as arruelas.
![](/globalassets/mediavalet/web-assets/pictures/expander/installation-instructions/15_dismounting_taping.png?mode=pad&width=600)
Bata no eixo alternativamente do lado esquerdo e direito até a tensão nas luvas for aliviada. Remova as luvas e eixo. NÃO DANIFIQUE AS ROSCAS.